|Place of Origin:||CHINA|
|Certification:||CE | RoHS | GB/T19001-2016/ISO 9001:2015|
|Packaging Details:||Plastic Double Tube | Paper Box/pieces|
|Supply Ability:||20million pieces / year|
|Material:||Polyaspartic Resin Polymer + High-grade Pigments And Special Additives||Classification:||Two Component Polyaspartic Tile Grout|
|Other Names:||Non Yellowing Grout | Weather Resistance Tile Grout | Ceramic Tile Grout | Tile Sealant||Color:||Sanded Khaki Grey | Pearl Grey|
|Shelf Life:||24 Months When Stored Correctly||Application:||Ceramic Tile | Marble | Stone Etc Joint Filling And Beatification|
|Feature:||Anti-mould | Stain Resistance | Waterproof | Durable | Easy To Clean | Easy Grouting||Keywords:||Epoxy Tile Grout | Epoxy Grout | Ready To Go Grout | Tile Sealant|
Polyaspartic Tile Grout P-30 is super weather resistance, the grout will not be yellowing and chalking at outdoor. It has high bonding strength, excellent physical properties such as non-sagging, tear/scratch/wear resistance. After curing, it is super anti-mildew, anti-bacterial, stain resistance, waterproof, moisture-proof, colorful, durable, smooth as porcelain, hard as diamond, bright as crystal, easy to clean, etc. The construction is very simple and convenient.
Perflex Polyaspartic Tile Grout P-30 is a double tube component joint grout, made of high-tech polymer polyaspartic, isocyanate hardener, high-grade pigments and additives. It is a semi-fluid liquid, packed into two-component plastic cartridge packaging, it can easily operate by automatic caulking gun. It’s 100% solid content, zero VOC, non-toxic materials that can be cured under low temperature -25℃.
|Testing Item||Resin A||Hardener B|
|Appearance||Semi-fluid liquid||Thixotropic paste|
|Blend Ratio(by volume)||A : B = 1 : 1|
|Working time(25℃*min)||20 min|
|Colloidal fluidity after blending||Thixotropic fluid|
|Wear Resistance (750 g.500 r)/g||0.030|
|Sagging after blending?||No sagging|
|Tensile Shear Strength/MPa||Standard condition||≥5.0|
|High/low temperature switch.||≥3.0|
|Water absorbent 25℃24 hour(%)||＜0.2|
|Waterproof / 24h||No change|
|Chemical Resistance / 2h||No change|
|Stain Resistance (Vinegar, soy, oil)/ 1h||No change|
|Testing condition: 21-25℃,relative humidity 45-55%. Constructed by caulking gun.|
1. After the mortar solidified, the ceramic tile crevice must be cleaned, the impurities and dust in the ceramic tile crevice must be cleaned up with wallpaper knife and vacuum cleaner.
2. Use cleaning wax on both sides of the gap beforehand with proper amount, pay attention not to wipe wax into the gap.
3. Twist the tube cap, install it on the head of the double-tube sealant, cut the spiral rubber nozzle obliquely at the head by 45 degrees (the opening size depends on the size of the tile seam), and then install it in the rubber gun.
4. Extrude about 20 cm colloid (in order to mix it fully and remove bubbles), then inject the glue into the crevice of ceramic tile.
5. Press the ready glue on the crevice with with the seam press or steel ball.
6. After 4-24 hours (depending on the temperature), the glue cures completely, scrape off the excess glue on both sides of the gap with a scraper.
Perflex Polyaspartic Tile Grout P-30 is suitable for bonding, filling and beautifying the joint of ceramic tile, marble and stone building materials such as ceramic tile floor, ceramic tile wall, washbasin, bathtub, toilet, kitchen table, door-crossing stone, etc. Especially P-30 is the best choice for balcony, roof, etc outdoor grouting.
|Tile Size Dosage||1MM Gap Width||1.5MM Gap Width||2MM Gap Width||2.5MM Gap Width|
400ml per plastic cartridge, 20 Cartridge per carton.
18 months if the product is stored in a dry and cool place away from light.
1. The Storage of sealant should not be less than 5℃.
2. Construction temperature is suitable in the range of 15-30℃, too low temperature will affect the curing time and strength.
3. Impurities, dust, grease, clear water and other substances shall not be allowed during construction.
4. Do not touch or trample until the sealant is completely cured.
5. After use, the remaining glue can be put on the cover and can continue to use.
Contact Person: Laura