Good Bonding Permeable Polyaspartic Clear Coat Permeable Floor Layer

PXF-600 Polyasartic Permeable Floor Coating - Good bonding | super weather resistance | Ultra clear

 

 

^{INTRODUCTION: PXF-600 is a two-component reaction curing transparent adhesive made of polyaspartic resin and HDI hardener, with interpenetrating structure and multi-functional chemist bonding, it can provide strong adhesion and substrate adhesion for permeable floor layer. Chemical toughening and modification can give the cured good flexibility, effectively avoid the excessive brittleness of traditional adhesive, effectively absorb the stress from the ground materials, and form a certain degree of rigid flexible Island effect, it’s has good anti- QUV properties, anti-aging and yellowing resistance.} 

^{FEATURE: The process of permeable stone flooring is to bond stone with adhesive by "point bonding", that requires the adhesive must has high adhesion, weather resistance, acid and alkali resistance, water erosion resistance, wear resistance and impact resistance.}

 

^{1-100% solid solvent-free formula, odorless, non-toxic, environmentally friendly.}

^{2-Strong and tough adhesion, ultra - clear, high gloss, wetting effect on color aggregate without changing the stone primary color.}

^{3- Adjustable viscosity to adapt to different climatic conditions and avoid back sealing of permeable products.}

^{4- Working time is 60min, can walk 6hours and fully open traffic for 24 hours after operation.}

^{5- Super weather resistance, anti-QUV, outdoor use.}

^{6- Color can be ultra-clear or being customized.}

 

^{APPLICATION: sidewalk, bicycle greenway, interior decorative wall, public square, road in park, campus road, community road, outdoor wall, pool floor, etc.}

 

 

 

 

 

^{1 - Preparation of colored stone aggregate}

• ^{The stone aggregate needs to be dried first. If there is too much stone powder, it is necessary to clean it.}

^{2- Stone aggregate & adhesive mixing}

• ^{Fully premix A and B two-component adhesive at the proposed ratio of 1:1, forcedly mix the stone aggregate to a uniform state by small cement mixer.}

^{3- Dumping and spreading}

•  ^{When pouring materials, firstly clean the dust on the base layer and ensure that substrate is dry and free of moisture.}

^{4- Stone aggregate spreading}

• ^{After the material is poured out, spread it as soon as possible. The operation time is 50-60 minutes. It can be spread manually or mechanically.}

^{5-Trimming and troweling}

• ^{When finishing, pay attention to the overall flatness, and timely repair the concave and convex.}

^{6- Waiting for forming}

• ^{After trimming, it can not be done after 6 hours, and the opening time can be fully released after 24 hours. Attention shall be paid to prevent personnel from stepping on it.}

 

 

 

^{Tools: small mixer, mud bucket, grinder, knife}

^{Stone Aggregate : according to the color type and stone size selected by customers.}

^{Material: PF-600 Polyaspartic adhesive}

 

Part A	Resin	Part B	Hardener
Appearance	Transparent	Appearance a	Transparent
Viscosity 25 ℃	1500mpas	Viscosity 25 ℃	1300mpas
Specific gravity 25 ℃	1.05	Specific gravity 25 ℃	1.1
Solid content	97%	Solid content	99%

 

^{PROPERTIES AFTER CURING}

7-day hardness	Shore D 75
Abrasion (CS17 wheel 750g, 500r) / Mg	25
Elongation at break (%)	5
Tensile strength (MPA)	25
Concrete adhesion (MPA)	2.2
Acid resistance	no change in 5% sulfuric acid
Alkali resistance	no change in 10% sodium hydroxide

 

 

 

^{- BLEND RATIO
Adhesive A : Adhesive B = 1 : 0.7 
Adhesive : Stone aggregate = (3 ~ 5) : 100}
 

 ^{- WORKING TIME}

Temperature (℃)	15	25	30
Mixed service life (min)	60	45	35

 

^{- CONSTRUCTION CONDITIONS 
Ambient temperature: 0 ℃ - 35 ℃, ambient humidity: ≤ 85%
Substrate temperature: must be more than 3 ℃ above the air dew point temperature
Cleaning agent: standard diluent of polyaspartic}

 

^{- DRY TIME AND RECOAT INTERVAL
Temperature (℃) : 25
Walking opening hours (HRS):  6
Vehicle opening hours (HRS) : 24}

^{The above data is only for guidance, and the real curing time is highly related to the ambient temperature and humidity.}

 

^{Storage time: Paint - 1 year | Curing agent - 9 month
Storage temperature: 5 ℃ - 35 ℃}

 

^{Paint: 20kg  |  Curing agent: 14kg}
 

<sup>- Avoid direct contact with skin and eyes.
- If the paint reach the skin, it shall be cleaned with appropriate detergent. If paint comes into eyes, use plenty of water to rinse and seek medical attention immediately.
- Ensure good ventilation.
- Paint contains combustible substances. Please keep away from sparks and do not smoke near the work area.
- All health and safety regulations shall be observed on site.</sup>
 

^{- The information provided in this product manual is entirely based on our knowledge in the laboratory and in practice. But because the use of products is usually beyond our control, we only guarantee the quality of products. We reserve the right to modify the specification without prior notice}